Soldering station 2in1 hotair and grotto ATTEN AT-8586 with fan in flask 750W

Бестселлер
47170557
-24%
130 $
Старая цена 171 $

Мы выстраиваем выгодные партнерские отношения с поставщиками электроинструментов Atten и отобрали для вас лучших производителей брендовых товаров из Европы, Америки, Турции и ОАЭ, специализируясь на аутлетах и дискаунтерах. Прямая доставка из-за рубежа до покупателя нашими логистическими решениями — это оптимизированные и экономичные решения, вы не переплачиваете в цене товара за расходы на торговые помещения и шоурумы. Заказ будет отправлен напрямую с нашего склада по указанному вами адресу, по цене недоступной для местных магазинов.

Оригинальные брендовые товары в широком ассортименте с вкусными скидками — так можно описать наш интернет магазин. Доставка заказа будет отслеживаться на всех этапах покупки и работает сразу после оплаты заказа.

  • Бренд Atten
  • Доставка из Польши
  • Почтовая доставка 21 мая
  • Стоимость доставки заказа в США от 80 $

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Promotion
BF20

Общие характеристики

Напряжение до
230 V
Напряжение от
230 V
Лаборатория будущего
Compatible
Паяльник - Вентилятор
yes
Припой - Горячий воздух
yes
Кондиционер паяного типа
Цифровой
Припой - показания реальной температуры
yes

Прочие свойства

EAN
5904422348496
Бренд
Atten

Свойства

Температура
150 - 480°C

Технические характеристики

Номинальная мощность
750 W

Описание

Description: ATTEN AT-8586 2-in-1 Hotair and Soldering Station with 750W Fan in Flask

A device combining the function of asolderingtip of50 Wwitha hotairstationof 700 W. The operating temperature of the soldering tip can be adjusted within the range from 150°C to 480°C. The maximum hot air blowing temperature (hotair) is 500°C. The ATTEN AT-8586 has a single digital display, showing values for the current operating mode. Adjustment of the operating parameters is done with a precise knob and buttons located on the front of the housing. The station can be used to solder SMD components and remove them from prototype boards.

In the offer of our shop there is a large selection of solderingstationsandaccessoriesnecessary during the soldering.

ATTEN AT-8586 2in1 hotair and soldering station.

Front panel of the ATTEN AT-8586soldering station.

Advantages of the ATTEN soldering station
  • The ATTEN AT-8586 combines the advantages of a traditional soldering station, equipped with a soldering iron and hot air blowing device
  • Can be used for SMD soldering and removal of SMD components from prototypes using a hotair
  • LED display showing the current operating temperature values
  • Control by a precise knob and function keys
  • LEDs indicating the current operating mode
  • Iron heater with low voltage to effectively protect sensitive electronic components
  • Intelligent cooling system and delayed shut-off function to extend the life of the device
  • Auto sleep function to save energy
  • Intelligent fault detection and signalling
  • Digital airflow step control (A25-A99)

Initial start up

  • When the equipment is delivered, do not immediately start it up.
  • The equipment should be left for approximately 12 hours at room temperature before start-up.
  • Any defect report caused by premature startup of the equipment will be rejected.
ATTEN AT-8586 Specifications

Hot Air Soldering Machine Specifications

  • Power: 700 W
  • Working temperature range: from 100°C to 500°C
  • Air flow stages: A25-A99
  • Air flow rate: 120 litres/minute
  • Air flow source: fan

Soldering tip specifications

  • Power: 50 W
  • Working temperature range: from 150°C to 480°C
  • Temperature stability: ± 2°C
  • Grounding impedance: below 2 Ω
  • Grounding voltage: less than 2 mV

Components of ATTEN AT-8586.

ATTEN AT-8586 2-in-1 Hotair and Soldering Station

General Specifications ATTEN AT-8586
  • Supply voltage 230 V AC / 50 Hz
  • Total power: 750 W
  • Recommended operating temperature: from 0°C to 40°C
  • Temperature control: precise knob, buttons
Contents of the set
  • Soldering station ATTEN AT-8586 : 1 pc.
  • Soldering iron holder 1 pcs.
  • Hot air holder : 1 pc.
  • Power cord: 1 pcs.
  • Blade cleaning sponge: 1 pcs.
  • Hotair tips: 3 pcs.
Useful links
  • Manufacturer's website
  • User manual

Доставка

Доставим товар из Германии от поставщика DESTE FZ LLC курьерской службой, в отделение Почты или пункт выдачи в вашем городе. Доставка в Армению, Казахстан, Грузию и Киргизию будет осуществлена доступными службами. Вы сможете выбрать желаемый способ доставки заказа в момент его оформления. Стоимость доставки зависит от выбранного вами метода и составит от 80 руб. Заказ будет доставлен за 10-30 дней, срок зависит от выбранного города. Если вы закажете этот товар прямо сейчас, доставим его 10 мая - 30 мая.

Доставка электроинструментов Atten напрямую из Германии в Москву, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие города России осуществляется надежными и проверенными нами службами доставки.

Как только заказ будет отправлен к вам с нашего склада, отслеживание заказа по номеру посылки станет доступным.