Odroid XU4 - Samsung Exynos5422 Octa-Core 2,0GHz/1,4GHz + 2GB RAM

Description of Odroid XU4 - Samsung Exynos5422 Octa-Core 2,0GHz / 1,4GHz + 2GB RAM

Minicomputer Odroid version C0 with a powerful processorSamsung Exynos5422 octa-corewith coresCortex-A15 2.0 GHz quad-core + Cortex-A7 with a clock frequency of 1.4 GHz quad-core. Board has2 GB of RAM LPDDR3, built-in Gigabit Ethernet port, HDMI 2.0 port and three USB slots including 2x USB 3.0, 30 GPIO, connectors for memory cards microSD and the IR receiver. Works with Ubuntu 15.04 or Android 4.2.2.

The device has 3 USB slots, HDMI connector and an Ethernet port, and many others.

 

What it takes to run minicomputer Odroid?

• The microSD card or eMMC memory - carrier, on which will be installed operating system
• AC adapter:
  • 5 V / 2 Afor version Odroid C0/C1+/C2
  • 5 V / 4 Afor version Odroid XU4
• Housing- protects minicomputer from the influence of external conditions
• HDMI cable- to connect the device to the monitor
• Mouse and keyboard - to control and input data into the device

 

In our store arre also availableoptional accessories- in type of adapter wi-fi,touchscreen display orthe module USB 3.0 - SATA

 

Operating system

Odroid C0 works with Ubuntu 15.04 and Android 4.2.2 based on kernel 3.10 LTS. The drive of device, can be a microSD card or a Flash memory eMMC 5.0 HS400.

 

Systems Ubuntu and Android can be downloaded fromthe manufacturer's website.

The installation is very simple -check out our manual!

 

Mounted radiator with fan is included.

 

Communication

Odroid has the main communication interfaces, which can be found in office computers of PC class. In addition to the previously listed connectors for audio and video, the user has at his or her disposal:

• HDMI port -  transfers the image on the monitor
• USB connectors, to which you can connect, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB. This version has 2 USB 3.0 and 1x USB 2.0
• GPIO x 30pin + 12pin 2mm raster- outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers, engines. Among them are the pins, supportting interfaces: I2C, SPI and UART. You musr purchase goldpin straps separately and solder them yourself.
• a slot for microSD - slot formemory cards microSD, on which can be installed the operating system.

 Odroid has a microSD slot on the top side of tile. Card is not included and can be purchased separately.

Connectors GPIO Odroid XU4 Board have a non-standard I/O raster of 2 mm.

 

Power

As a power source, the system uses theDC connector 5.5 x 2.1 mm. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 and a minimum output current of the used power supply shall be not less than 4.0 A. You will finda specialpower supply in our assortment.

 

Cases

In our assortment you will findspecial housings that protects minikcomputer Odroid from external conditions. Special power supplies also available.

 

Photo of minicomputer Odroid ina special housing.

 

Specifications and comparison

 

Basic information   Model Odroid C0 Odroid C1+ Odroid C2 Odroid XU4 Specification Processor Amlogic S805 Amlogic S805 Amlogic S905 Samsung Exynos5422 The core

Quad-Core 32-bit

ARM Cortex A5

Quad-Core 32-bit

ARM Cortex A5

Quad-Core 64-bit

ARM Cortex-A53

Octa-Core

ARM Cortex-A15

ARM Cortex™-A7

Graphics

ARM Mali 450MP

OpenGL ES

2.0/1.1

ARM Mali 450MP

OpenGL ES

2.0/1.1

ARM Mali 450MP

OpenGL ES

2.0/1.1

3D Mali-T628 MP6

OpenGL ES

3.0/2.0/1.1

Systems

Ubuntu 14.04

Android 4.4

Kernel 3.10 LTS

Ubuntu 14.04

Android 4.4

Kernel 3.10 LTS

Ubuntu 16.04

Android 5.1

Kernel 3.14 LTS

Ubuntu 15.04

Android 4.4.2

Kernel 3.10 LTS

Clock frequency 1.5 GHz 1.5 GHz 1.5 GHz 2 GHz / 1.4 GHz Architecture ARMv7 ARMv7 ARMv8 ARMv7-A RAM

1 GB DDR3

SDRAM

1 GB DDR3

SDRAM 792MHz

2 GB DDR3

SDRAM 792Mhz

2 GB LPDDR3

RAM 750Mhz Memory

microSD memory card

UHS1

eMMC4.5 HS200

microSD memory card

UHS1 up to 16 GB

eMMC4.5

microSD memory card

UHS1 with capacity up to 128 GB

eMMC5.0

microSD memory card

The UHS1 up to 64 GB

eMMC5.0 GPIO slot

Connector 40-pin

+ 7-pin I2S

(to solder)

Connector 40-pin

+ 7-pin I2S

Connector 40-pin

+ 7-pin I2S

Connector 30-pin

+ 12 pin I2S

raster 2mm

Power

5 V / 2 A

DC Jack

5 V / 2 A

DC Jack

5 V / 2 A

DC Jack

5 V / 4 A

DC 2,5x2,1mm

Tile sizes 58x56x11mm 85x56x18mm 85x56x18mm 82x58x22mm Interfaces USB-Host

2 x USB 2.0

(optional soldering)

4x USB 2.0

slot type a

4x USB 2.0

slot type a

2x USB 3.0

1x USB 2.0

slot type a

USB OTG -

1x microUSB

1x microUSB - Network interface -

Ethernet

10/100/1000

Mbit/s

Ethernet

10/100/1000

Mbit/s

Ethernet

10/100/1000

Mbit/s

The RTC system Built-in Built-in - - Video HDMI HDMI HDMI 2.0 4K/60 Hz HDMI 1.4 a Audio

HDMI / I2S

HDMi

HDMI / I2S

HDMI ADC

2 channels

10-bits

2 channels

10-bits

2 channels

10-bits

2 channels

10-bits

Communication

UART, SPI, I2C,

GPIO, ADC

UART, SPI, I2C,

GPIO, ADC

UART, SPI, I2C,

GPIO, ADC

UART, SPI, I2C,

GPIO, ADC

Video

Introducing the minicomputer Odroid XU4

 

Useful links

• Operating systems to download - Wiki
• Choosing a microSD card
• System installation - a guide in Polish 
• System installation - user manual from the manufacturer
• The scheme of the board Odroid XU4
• Technical drawing - dimensions of Odroid XU4
• Forum of users of Odroid
• Certificates to download
• Documentation of CPU Amlogic S805