Odroid M1 - minicomputer with Rockchip RK3568B2 processor + 8 GB RAM

Odroid M1 is a single board minicomputer equipped with a wide range of interfaces. The brain of the board is the Cortex-A55 quad-core processor (with low energy consumption and high performance) and the Mali-G52 graphics processor. Odroid M1 is also equipped with 8 GB of RAM and a connector for eMMC memory and microSD cards , Ethernet, HDMI and USB 3.0. An efficient heat sink is placed around the module, which helps to cool the entire system during operation.

Odroid M1 - minicomputer with Rockchip RK3568B2 processor + 8 GB RAM.

1. Rockchip RK3568B2 processor
2. LPDDR4 RAM
3. Micro USB 2.0 port
4. RJ45 Ethernet port (10/100/1000 Mb / s)
5. HDMI 2.0
6. USB 2.0 port x2
7. USB 3.0 port x2
8. DC jack for DC power supply
9. M.2 NVMe M-Key PCIe3.0 2-lane
10. GPIO x40 pins
11. MIPI CSI 2 Lane
12. MIPI DSI 4 Lane
13. 3.5mm headphone jack
14. Mono speaker output (1.3 W into 8 Ω load)
15. SPI recovery switch
16. SPI Flash 16 MB
17. EMMC module socket
18. Infrared receiver
19. RTC battery holder
20. Reset jumper and power jumper
21. MicroSD memory card slot
22. SATA3
23. SATA power (5V only)
24. UART for the system console
25. System LED indicators x2
26. M.2 LED indicator

The Petitboot program pre-installed in the SPI Flash memory helps you to easily and quickly manage different versions of the operating system and supports booting from microSD, eMMC, NVMe, SATA and USB mass storage devices. Moreover, since it is possible to install the operating system online via the network, the complicated procedure of downloading and flashing the operating system image has been significantly reduced.

The Odroid M1 board has a neural network processing unit (NPU) that provides up to 0.8 TOPS. On the Ubuntu Linux operating system, the manufacturer launched various models of TensorFlow Lite and ONNX.

The Odroid M1 heatsink has special mounting holes for mounting the housing.

On the Odroid board, you can directly install an M.2 NVMe mass storage device with dimensions of 22 mm x 80 mm. The M.2 connector has a 2-channel PCIe 3.0 configuration that provides fast sequential access with a performance of 1600 MB / s. Please note that M.2 SATA storage devices cannot be used . M.2 slot only supports PCIe (M-Key) interface.

Odroid also has a single native SATA 3.0 port (not USB), which allows you to connect a 2.5 "hard drive or SSD NAND storage device. The SATA interface provides sequential access speed of almost 500 MB / s. To use 3.5" a separate external 12 V SATA power supply is required for the hard drive.

In our offer you will also find a special case prepared with the Odroid M1 in mind. It has an elegant appearance, provides protection against mechanical damage and dirt, and is at the same time extremely efficient - it effectively cools the minicomputer even during high processor load. The housing is blue and made of metal. It has a structure that allows it to be securely attached to the heat sink frame of the minicomputer. The front and rear covers are made of gold-plated printed circuit boards.

The case for Odroid M1 is not part of the set - it can be purchased separately in our store.

• Processor: Rockchip RK3568B2
  • L1 instruction cache: 32 KB, 4-way association, 64 bytes of lines, shared by 1 processor
  • L1 data cache: 32 KB, 4-way association, 64 bytes of lines, shared by 1 CPU
  • L3 data cache: 512KB, 16-way association, 64 bytes line, shared by Quad-Core Cortex-A55 processor (1.992 GHz)
  • ARMv8-A architecture with Neon and Crypto extensions
  • Mali-G52 MP2 graphics processor with 4 execution engines (650 MHz)
• NPU :
  • 0.8Tops / INT8, integrated high-performance AI RKNN NPU accelerator
  • Supports Caffe / TensorFlow / TFLite / ONNX / PyTorch / Keras / Darknet switching
• Memory:
  • LPDDR4 8 GB with 32-bit bus
  • Data transfer rate: 3120 MT / s to 1560 MHz
• Networking:
  • 1 x eMMC slot
  • 1 x Micro SD slot (DS / HS mode for UHS-I SDR104)
  • 1 x NVME M.2 SSD (PCIe 3.0 x 2)
  • 1 x SATA3.0
• Network:
  • GbE LAN port (RJ45 10/100/1000 Mb / s)
    • Realtek RTL8211F (Ethernet transceiver)
    • Led
  • Green LED: Flashing by data traffic on 100Mbps connection
  • Amber LED: Flashing by data traffic on a 1000Mbps connection
• Video:
  • HDMI 2.0 (up to 4K @ 60Hz with HDR, CEC, EDID)
  • MIPI DSI (works with 800 x 1280 LCD)
• Audio:
  • HDMI digital output
  • 3.5mm jack connector
  • Mono speaker output
• External I / O Ports:
  • 2 x USB 3.0 ports (or 1 x USB 3.0 host + 1 x USB 2.0 OTG port)
  • 2 x USB 2.0 port
  • UART (Debugging)
  • SATA
  • MIPI-CSI camera interface
  • MIPI-DSI LCD interface
  • 40-pin GPIO connector
• Other functions:
  • IR receiver
  • RTC and backup battery holder
  • LED diodes:
    • Red (PWR) - Steady light after connecting the power supply
    • Blue (ALIVE) - Flashes while the kernel is running
• Power supply:
  • DC jack: 5.5mm outer (-) diameter, 2.1mm inner (+) diameter
  • DC input: 7.5V to 15.5V (DC 12V / 2A power adapter recommended)
  • Energy consumption:
    • IDLE: 1.25W
    • CPU load: approximately 4.44 W
• Board dimensions: 90 x 122 x 16 mm
• Heatsink dimensions: 100 mm x 123 mm x 19 mm
• Weight: 253 g

• Manufacturer's website