LattePanda V1 2GB RAM + 32GB EEMC Intel Quad-Core WiFi - Windows 10

Description

Minicomputer with Windows 10 installed! Equipped with a processorIntel Cherry Trail Z8350 Quad Core 1.8 GHz. In addition, it has2 GB of RAMand32 GB of built-in memory EMMC,wi-fi and Bluetooth 4.0, 2x USB 2.0, 1x USB 3.0, microSD slot, Ethernet port. In addition, Panda feature microcontrollerATmega32u4 known from Arduino Leonardo, which controls 20 GPIOs. This combination allows the direct programming of the embedded Leonardo of Windows 10 via the serial interface.

 

 

LattePanda has installed operating system Windows 10!

 

What it takes to run LattePanda?

• MicroUSB power supply - with minimum load current of 2 A, for example:power supplies designed for Raspberry Pi.
• HDMI cable- to connect the device to the monitor.
• Mouse and keyboard - to control and input data into the device.

 

First run

Starting LattePanda is very easy, to enjoy the OS from desktop Windows 10 you have to:

1. Connect the power adapter with microUSB connector with performance above 2 A, for example,the power supply for the Raspberry Pi.
2. The led located under the device should illuminate red.
3. Then just press and hold the Power button (the first one next to the Ethernet slot) for approx. 1 sec.
4. Minicomputer will start, showing on the screen the logo LattePanda.
5. Now, you just have to configure Windows 10 in the same way as, for example, after buying a new laptop.

 

LattePanda also has connectors formodules and sensors from the DFRobot Gravity.

 

Operating system

Disk of LattePanda is embedded memory EMMC. Windows 10's operating system is already installed by the manufacturer. Just run minicomputer and configure Windows to your likings.

 

The picture and sound

LattePanda has aHDMI port through which you can send picture and sound.

 

In our offer, you will find also:display IPS 7"anda touchpadfor LattePanda.

 

Power

As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage have values of 5 V and the minimum current must be not less than 2.0 A. This criteria are met by the power supplies for the Raspberry Pi 3B and 2B minicomputer.

 

Minicomputer LattePanda - top view.

 

Communication

LattePanda has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors for audio and video, the user has at his or her disposal:

• three connectors: USB 2x USB 2.0 + 1x USB 3.0 to which you can connect, for example, a mouse, keyboard or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB.
• Ethernet slot, that is the ability to directly connect to the LOCAL network
• the wi-fi moduleallows communication with wireless network 802.11 b g n
• Bluetooth 4.0- allows data transmission through the interface
• GPIO- outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of engines. 20 pins are navigated through the coprocessor Atmega32u4 known from boardArduino Leonardo.

 

Distribution of connectors for minicomputer LattePanda.

 

Compatible with Arduino

Minicomputer has additional microcontroller Atmega32u4 - known from boardArduino Leonardo. This system operates 20 digital I/O and interfaces designed to communicate with modules and sensors like: UART, I2C, SPI. In addition, the manufacturer installed several connectors formodules of the series DFRobot Gravity.

 

Check out how to use LattePanda as Arduino!

In our offer you will finda special starter kitwith sensors and modules for LattePanda

Specifications and comparison with Rasberry Pi 3 Basic information   Model LattePanda 2GB LattePanda 4GB Raspberry Pi 3 B Technical specification of Processor chipset

Intel Cherry

Trail Z8350

Intel Cherry

Trail Z8350

Broadcom

BCM2837 64-bit

The number of cores 4 (Quad Core) 4 (Quad Core)

4 (Quad-Core)

ARM Cortex

Operating systems

Windows10 with license

Windows10 without a license

Windows10 without a license

Linux Raspbian

Windows 10 flight

Clock frequency 1.8 GHz 1.8 GHz 1.2 GHz RAM 2 GB DDR3L 4 GB DDR3L

1 GB LPDDR2

Memory

32GB EMMC

(built-in)

64 GB EMMC

(built-in)

microSD memory card Coprocessor

Atmega32u4

in accordance with

Arduino Leonardo

supports GPIO

Atmega32u4

in accordance with

Arduino Leonardo

supports GPIO

-

Graphics

Intel HD Graphics

200 MHz (500 MHz)

1920x1080px

Intel HD Graphics

200 MHz (500 MHz)

1920x1080px

VideoCore IV

3D graphics core

GPIO slot

• Connector 2x10 pinfemale
• GPIO connector Intel
• Connectors forsensorsfrom the Gravity series

• Connector 2x10 pinfemale
• GPIO connector Intel
• Connectors forsensorsfrom the Gravity series

Connector 2x20 pin

male

The number of GPIO

20 - Atmega32u4

2 - Intel

20 - Atmega32u4

2 - Intel

40 - Broadcom

Power

5.0 V / 2.0 A

via microUSB

5.0 V / 2.0 A

via microUSB

A 5.1 V / 2.5 A

via microUSB

Tile sizes 88 x 70 mm 88 x 70 mm 85 x 56 mm Interfaces USB interface

2x USB 2.0 - type A

1x USB 3.0 - type A

2x USB 2.0 - type A

1x USB 3.0 - type A

4x USB 2.0 - type A Network interface

Ethernet port

10/100 Mbps

Ethernet port

10/100 Mbps

Ethernet port 10/100 Mbps The Wi-Fi Interface

802.11 b/g/n 150 Mbps

02.11 b/g/n 150 Mbps 802.11 b/g/n 150 Mbps Bluetooth Low Energy, BLE 4.0 Low Energy, BLE 4.0 Low Energy, BLE 4.1 Camera - - the CSI slot

Touch display

special slot special slot slot for DSI Video

HDMI HD 1080p

30 fps

HDMI HD 1080px

30 fps

HDMI HD 1080px / 30 fps Audio HDMI + audio Jack HDMI + audio Jack HDMI + audio Jack Communication UART, SPI, I2C, GPIO UART, SPI, I2C, GPIO UART, SPI, I2C, GPIO

 

Included

• Minicomputer LattePanda
• External wi-fi antenna

 

Useful links

• Project page of LattePanda
• User manual for LattePanda
• Website of supplier: DFrobot DFR0418
• Specification of CPU and graphics card
• Test of graphics cards - Benchmark
• Website LattePanda in the service KickStarter
• Project Pinball