BOBIKE Go Maxi Rear Child Bike Seat Refurbished

Refurbished reasons: It has some slight signs of use. It has some barely visible scratches on the surface. It does not have its original box and packaging.

For child safety and for your peace of mind, Bobike has developed the perfect childcarrying solution that’s suitable for a wide range of adult bicycles.Our ergonomic child seats are all built with safety and comfort as the primary goals.In this manual, you will find information on attaching the child bicycle seat to the frameof your bicycle. Technical Features: - This child bicycle seat must not be mounted to bicycles fitted with rear shock absorbers. - This child bicycle seat must not be mounted to a racing bicycle with drop handlebar. - This child bicycle seat must not be mounted to Motorized Vehicles such as Mopeds and Scooters. - This child bicycle seat must not be mounted in bicycles with triangular, square or carbon fiber frames. - This child bicycle seat must be assembled on bicycles with round and oval frames with diameters ranging from Ø28 to Ø40 mm. - The child bicycle seat must be assembled on bicycles with wheels with diameters of 26” and 28”. - This child bicycle seat is only suitable for carrying children with a maximum weight of 22 Kg (and children with recommended ages ranging from 9 months to 5 years of age - with the weight as the decisive variable). - The total weight of the cyclist and the child transported must not exceed the maximum permitted load permitted for the bicycle. Information on the maximum load can be found in the operating instructions of the bicycle. You can also contact the manufacturer for this question. - The seat may only be mounted on a bicycle suitable for the attachment of such additional loads. - The position of the child bicycle seat must be adjusted so that the bicycle rider does not touch the child bicycle seat with the feet when in motion. - It’s very important to adjust correctly the seat and its component parts for optimumcomfort and safety of the child. It’s also important that the seat does not slope forward, so that the child does not tend to slide out of it. It’s also important that the backrestslope backward slightly. - Check if all parts of the bicycle function correctly with the child bicycle seat mounted. - Check the instructions of the bicycle, and If you have any doubts on fitting the child bicycle seat to your bicycle, please contact your bicycle supplier for further information. Assembly Instructions: - Cut the plastic straps that hold the mounting block (I). - Use the allen key No. 5 (I5) to loosen and remove the Metallic bracket support/ Mobile stand (J3). Desingage the Metallic bar support (J3) by pulling it backwards.After removing this part (J3) you will no longer need to use it, so we give it a functionalpurpose – you can keep it and use it as a mobile stand. - Desingage and remove the metallic bracket (H) from the child seat, pulling it backwards. - Desingage and remove the metallic mounting plate (J1). - Hold the metallic bracket (H) the same as in the picture and pass it through the opening in the child bicycle seat. - In order to adjust the child bicycle seat according to the bicycle size, set the metallic bracket (H) into one of the three allowed positions to move the seat backward or forward. At the beginning we suggest to place it on the position No. 3. - Insert the metallic mounting plate (J1) on the grooves of the child bicycle seat, and close it as indicated in the picture. - Place the screw (J2) into the metallic mounting plate (J1) fixing both into to the seat(A). Then tighten it securely with the key (I5). Tighten tightly so that the metal bracket (H)is securely fastened. This step is extremely important for the safety of the child. - Remove the screws (I1) on the mounting block (I), with the Allen key no. 5 (I5). 10. Before placing the block onto the frame, make sure that the protective rubber (I8) iscorrectly positioned on front of the block. - Place the main body of the mounting block (I2) on the front of the bicycle frame, and then place the metallic mounting plate (I4).Note: If they are cables in this area make sure that they are correctly positioned in thecentral groove of the metallic plate, (between the protective rubber (I8) and the grooveof the mounting plate (I4) and are able to move freely). - Place the washer (I6) in the M8 screws (I1), and then screw them on to the mounting block (I). Tighten the screws, with the Key (I5), so that the mounting block (I) is securedbut not fully tightened so that, if necessary, you can adjust the height later. However,note that it should be tight to make it easier to complete the next step. You need totighten the 4 screws diagonally and in stages. Check the safety of the fastenersregularly. - Place the edges of the metallic bracket (H) at the holes of the mounting block (I) untilyou hear a click indicating the lock, and until the 2 green safety device indicators pop upon the front of the mounting block. The child bicycle seat will only be properly installedwhen the 2 green safety device indicators are visible. This step is extremely importantfor the child’s safety.